manualshive.com logo in svg

Stryker TriaDyne III Proventa 2030, Maintenance Manual, Page: 39 / 113

Share
Download
Stryker TriaDyne III Proventa 2030 Maintenance Manual Download Page 39

Service Information

38

FOWLER POTENTIOMETER REPLACEMENT

Required  Tools:

T27 Torx

Wire Cutters

1/2” Open End Wrench

7/64” Allen Wrench

Replacement Procedure:

1. Manually crank the knee section up until it stops.
2. Using a T27 Torx, remove the four screws holding the litter access cover to the litter and remove the cover.
3. Using a 7/64” Allen wrench, loosen the screw holding the linkage to the pot. shaft and remove the linkage

from the shaft.

4. Using a 1/2” open end wrench, remove the nut holding the potentiometer to the frame.
5. Using wire cutters, remove the cable ties from the cable.  Unplug the cable from the CPU and remove the

pot.

6. Reverse the above procedure to install the replacement potentiometer.
7. The new potentiometer must be calibrated after it has been installed.
8. The Fowler pot. should be set at 150 ohms (

$

 10 ohms) in the full down position.  This reading must be

taken from pins 3 and 4 on the connector with the pot. unplugged from the board.  After the correct ohm

reading is achieved, tighten the screw on the linkage.

9. Reinstall the litter cover.

10. Perform the potentiometer “burn

−

in” procedure as described on page 39.

Summary of Contents for TriaDyne III Proventa 2030


















































































































Reviews:

No comments