manualshive.com logo in svg

Stryker TriaDyne III Proventa 2030, Maintenance Manual, Page: 31 / 113

Share
Download
Stryker TriaDyne III Proventa 2030 Maintenance Manual Download Page 31

Service Information

30

POWER AND SENSOR COIL CORD REPLACEMENT

Required Tools:

#2 Phillips Screwdriver

Side Cutters

5/16” Socket Wrench

Bungee Cord (or equivalent)

5/16” Nut Driver

Floor Jack

2x4 (or Equivalent)

Procedure:
NOTE

If you need more space to work under the base frame, place a 2x4 across the base frame rails and use a

floor jack to raise the base frame off the floor.
1. Unplug the bed power cord from the wall socket.
2. Using a 5/16” socket wrench, remove the five bolts holding the lower lift cover to the base and remove

the cover.

3. Using a #2 Phillips screwdriver, remove the three screws holding the upper lift cover to the base.  If you

want, hold the covers out of the way by using bungee cords (or the equivalent) to secure them to the litter

top.

4. Using side cutters, cut the cable ties holding the power and sensor coil cords to the base.  Remove the

ground wire coming from the sensor cord that is attached to the base (note the star washer arrangement).

5. Disconnect the cables going to the motor and the lift potentiometer (at the head end, the sensor cord is

also attached to the brake switch sensor).

6. Pull both cords up through the frame of the bed and the lift housing.
7. Using a 5/16” socket wrench, remove the two screws (A) holding the cable clamps* to the top of the lift

housing.

8. Using a 5/16” socket wrench, remove the two screws (B) securing the cable clamps* to the underside

of the header crossbar assembly.

9. Pull both coil cords up through the header crossbar assembly.

10. Disconnect the power and sensor coil cords from the connectors.
11. The cords should now be completely removed from the bed.  Reverse the above steps to install the new

power and sensor cords.*

  

CAUTION

* When the power and sensor coil cords are being replaced, secure the cable clamps to the cords at the first

coil both on the top and on the bottom to assure there is not too much slack in the cords between the top of

the lift housing assembly and the bottom of the header crossbar.  Be sure the clamps are fastened at exactly

the correct angle, as shown by the arrows in the illustration.  Arrange the cords exactly as shown in the illustra-

tion (left in front of right).  

If this is not done correctly, damage to the cords will result.

Summary of Contents for TriaDyne III Proventa 2030


















































































































Reviews:

No comments