manualshive.com logo in svg

Stryker TriaDyne III Proventa 2030, Maintenance Manual, Page: 28 / 113

Share
Download
Stryker TriaDyne III Proventa 2030 Maintenance Manual Download Page 28

Service Information

27

LIFT POTENTIOMETER REPLACEMENT AND ADJUSTMENT

Required Tools:

#2 Phillips Screwdriver

Bungee Cord (or equivalent)

5/16” Socket Wrench

3/8” Open End Wrench

Side Cutters

B

C

A

B

Procedure:

1. Raise the litter to the full up position.
2. Unplug the bed power cord from the wall socket.
3. Using a 5/16” socket wrench, remove the five bolts holding the lower lift cover to the base and remove

the  cover.  If you want, hold the covers out of the way by using bungee cords (or the equivalent) to secure

them to the litter top.

4. Using a #2 Phillips screwdriver, remove the three screws holding the upper lift cover to the base.  If you

want, hold the covers out of the way by using bungee cords (or the equivalent) to secure them to the litter

top.

5. Using side cutters, cut the cable tie (A) holding the pot cable to the coil cord.
6. Unplug the pot cable from the sensor coil cord.  If replacing a pot at the head end of the bed, unplug the

cables attached to the brake sensor switch.

7. Pull the pot cable up through the base.
8. Using a 3/8” open end wrench, remove the two bolts (B) holding the pot housing (C) to the lift housing.

Summary of Contents for TriaDyne III Proventa 2030


















































































































Reviews:

No comments