manualshive.com logo in svg

Stryker TriaDyne III Proventa 2030, Maintenance Manual, Page: 38 / 113

Share
Download
Stryker TriaDyne III Proventa 2030 Maintenance Manual Download Page 38

Service Information

37

POWER SUPPLY REMOVAL AND REPLACEMENT

Required  Tools:

T27 Torx

Needle

−

Nose Pliers

Procedure:

1. Run the litter to the full up position and remove the mattress from the bed.
2. Fold the foot section back toward the head end of the bed.  Electrically run the knee section to full up.

If the knee section will not move electrically, pull the foot section toward the head end of the bed while

pulling the CPR release handle (located at the head end of the bed).  The knee section will raise.

3. Using a T27 torx, remove the four screws holding the cover to the actuator box and remove the cover.
4. Properly ground yourself (see 22)
5. Unplug all electrical connections from the power supply.
6. Using needle

−

nose pliers, squeeze the four stand

−

offs supporting the power supply and pull up gently

on the power supply to remove it.

7. Reverse steps 2 through 5 to install the new power supply.
8. Verify the bed is working properly before returning it to service.

CPU BOARD REMOVAL AND REPLACEMENT

Required  Tools:

T27 Torx

Needle

−

Nose Pliers

Replacement Procedure:

1. Run the litter to the full up position and remove the mattress from the bed.
2. Fold the foot section back toward the head end of the bed.  Electrically run the knee section to full up.

If the knee section will not move electrically, pull the foot section toward the head end of the bed while

pulling the CPR release handle (located at the head end of the bed).  The knee section will raise.

3. Using a T27 torx, remove the four screws holding the cover to the actuator box and remove the cover.
4. Properly ground yourself (see 22)
5. Unplug all electrical connections from the CPU board.
6. Press the six stand

−

offs away from the board while gently lifting the board up and out.

7. Install the replacement CPU board.

NOTE

After the replacement CPU board is installed, the “burn

−

in” procedure must be performed for the Fowler and

lift motor potentiometers.

If the bed is equipped with a scale system, a scale calibration procedure must also be performed after the

replacement CPU board is installed (see page 33).

Summary of Contents for TriaDyne III Proventa 2030


















































































































Reviews:

No comments