Stryker TriaDyne III Proventa 2030 Maintenance Manual Download Page 36 | Manualshive

Page: 36 / 113

Stryker TriaDyne III Proventa 2030 Maintenance Manual Download Page 36

Service Information

35

HEAD MOTOR REMOVAL AND REPLACEMENT

Required Tools:

T27 Torx

7/16” Socket Wrench

3/8” Socket Wrench

Wire Cutters

Procedure:

1. Run the litter to the full up position and remove the mattress from the bed.
2. Fold the foot section back toward the head end of the bed. Electrically run the knee section to full up.

If the knee section will not move electrically, pull the foot section toward the head end of the bed while

pulling the CPR release handle (located at the head end of the bed). The knee section will raise.

3. Using a T27 torx, remove the four screws holding the cover to the actuator box and remove the cover.
4. Remove the two CPR release cables from the CPR release bracket. Using a 3/8” socket wrench under-

neath the actuator box, remove the two bolts holding the release bracket to the actuator box and remove

the bracket from the actuator box.

5. Disconnect all the electrical connections going to the head motor and move aside any wiring that could

interfere with the removal of the motor.

6. Using a 3/8” socket wrench underneath the actuator box, remove the four bolts holding the motor mount-

ing bracket to the actuator box. Lift up and out on the motor to remove it.

7. Remove the motor mounting bracket from the old motor and install it on the replacement motor.
8. Reverse steps 3 through 6 to install the replacement motor.
9. Verify the bed is working properly before returning it to service.

«
...
34
35
36
37
38
...
»

Summary of Contents for TriaDyne III Proventa 2030


















































































































Reviews:

No comments