manualshive.com logo in svg

Stryker TriaDyne III Proventa 2030, Maintenance Manual, Page: 35 / 113

Share
Download
Stryker TriaDyne III Proventa 2030 Maintenance Manual Download Page 35

Service Information

34

SCALE SYSTEM DIAGNOSTICS AND CALIBRATION (CONTINUED)

Scale Calibration (Continued):

6. If exactly 50 pounds is not available, change the display to match the weight you are using.  Pressing

the CHANGE EQUIP button will move the cursor position to the right.  Pressing the up arrow (ZERO)

button will increase the numbers.  Pressing the down arrow (SCALE ON/OFF) button will decrease the

numbers.  Scroll through the numbers until they match the weight you will use for calibration.

7. Place the 50 pound calibrated weight in the center of the bed.  Press and release the ENTER button and

the LCD will display “PRESS REV. TREND”.  Press and hold the button with the Reverse Trendelenburg

symbol (feet down/head up) until the bed stops.  Release the button and the LCD will display “DO NOT

TOUCH BED”.  Press and hold the Reverse Trendelenburg button again until the bed stops.  Release

the button and the LCD will display “DO NOT TOUCH BED”.

8. The LCD will display “PRESS TREND.”  Press and hold the button with the Trendelenburg symbol (feet

up/head down) until the bed stops.  Release the button and the LCD will display “DO NOT TOUCH BED”.

Press and hold the Trend button again until the bed stops.  Release the button and the LCD will display

“DO NOT TOUCH BED”.

9. Repeat steps 5 

−

 8 with 200 pounds.

10. The LCD will display the weight.  This indicates the calibration procedure is complete.

11. Level the bed at a full up or full down position.  Remove the weight and zero the bed.
12. Verify scale accuracy and functionality before returning the bed to service.

LOAD CELL REPLACEMENT

Required  Tools:

9/16” Socket Wrench

9/16” Open End Wrench

Saw Horse (or Equivalent)

Wire Cutters

Replacement Procedure:

1. Raise the Fowler or knee section, depending which end of the litter needs service.
2. Unplug the load cell connector from the load cell cable.
3. Using wire cutters, remove the wire ties holding the cable to the frame.
4. Using a 9/16” socket and a 9/16” open end wrench, remove the two bolts holding the load cell to the litter

cross tube and remove the load cell.

5. Using a saw horse, support the litter at the end where the load cell was removed.  Reverse the above

procedure to install the new load cell.

NOTE

Scale calibration procedure must be performed after the load cell is replaced (see 33).

Summary of Contents for TriaDyne III Proventa 2030


















































































































Reviews:

No comments