manualshive.com logo in svg

Stryker TriaDyne III Proventa 2030, Maintenance Manual, Page: 112 / 113

Share
Download
Stryker TriaDyne III Proventa 2030 Maintenance Manual Download Page 112

Warranty

111

Limited Warranty:

Stryker Medical Division, a division of Stryker Corporation, warrants to the original purchaser that its products

should be free from defects in material and workmanship for a period of one (1) year after date of delivery.

Stryker’s obligation under this warranty is expressly limited to supplying replacement parts and labor for, or

replacing, at its option, any product which is, in the sole discretion of Stryker, found to be defective.  Stryker

warrants to the original purchaser that the frame and welds on its beds will be free from structural defects

for as long as the original purchaser owns the bed.  If requested by Stryker, products or parts for which a

warranty claim is made shall be returned prepaid to Stryker’s factory.  Any improper use or any alteration or

repair by others in such manner as in Stryker’s judgement affects the product materially and adversely shall

void this warranty.  Any repair of Stryker products using parts not provided or authorized by Stryker shall void

this warranty.  No employee or representative of Stryker is authorized to change this warranty in any way.
Stryker Medical beds are designed for a 10 year expected life under normal use conditions and appropriate

periodic maintenance as described in the maintenance manual for each device.
This statement constitutes Stryker’s entire warranty with respect to the aforesaid equipment.  STRYKER

MAKES NO OTHER WARRANTY OR REPRESENTATION, EITHER EXPRESSED OR IMPLIED, EXCEPT

AS SET FORTH HEREIN.  THERE IS NO WARRANTY OF MERCHANTABILITY AND THERE ARE NO

WARRANTIES OF FITNESS FOR ANY PARTICULAR PURPOSE.  IN NO EVENT SHALL STRYKER BE

LIABLE HEREUNDER FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OR IN ANY

MANNER RELATED TO SALES OR USE OF ANY SUCH EQUIPMENT.

Return Authorization:

Merchandise cannot be returned without approval from the Stryker Customer Service Department.  An autho-

rization number will be provided which must be printed on the returned merchandise.  Stryker reserves the

right to charge shipping and restocking fees on returned items.
SPECIAL, MODIFIED, OR DISCONTINUED ITEMS NOT SUBJECT TO RETURN.

Damaged Merchandise:

ICC Regulations require that claims for damaged merchandise must be made with the carrier within fifteen

(15) days of receipt of merchandise.  DO NOT ACCEPT DAMAGED SHIPMENTS UNLESS SUCH DAMAGE

IS NOTED ON THE DELIVERY RECEIPT AT THE TIME OF RECEIPT.  Upon prompt notification, Stryker

will file a freight claim with the appropriate carrier for damages incurred.  Claim will be limited in amount to

the actual replacement cost.  In the event that this information is not received by Stryker within the fifteen

(15) day period following the delivery of the merchandise, or the damage was not noted on the delivery receipt

at the time of receipt, the customer will be responsible for payment of the original invoice in full.
Claims for any short shipment must be made within thirty (30) days of invoice.

International Warranty Clause:

This warranty reflects U.S. domestic policy.  Warranty outside the U.S. may vary by country.  Please contact

your local Stryker Medical representative for additional information.

Summary of Contents for TriaDyne III Proventa 2030


















































































































Reviews:

No comments