manualshive.com logo in svg

Stryker TriaDyne III Proventa 2030, Maintenance Manual, Page: 7 / 113

Share
Download
Stryker TriaDyne III Proventa 2030 Maintenance Manual Download Page 7

Introduction

6

SET

−

UP PROCEDURES

It is important that the bed is working properly before it is put into service.  The following list will help ensure

that each part of the bed is tested.

Plug the bed into a properly grounded, hospital grade wall receptacle and ensure the ”Power” LED light

at the foot end of the bed comes on.

  

WARNING

The 2030 is equipped with a hospital grade plug for protection against shock hazard.  It must be plugged di-

rectly into a properly grounded three

−

prong receptacle.  Grounding reliability can be achieved only when a

hospital grade receptacle is used.

Ensure the siderails raise, lower and store smoothly and lock in the up and intermediate positions.

Ensure that all four casters lock when the brake pedal is engaged

NOTE

Ensure that the ”Brake Not Set” LEDs located on the outside of the head end siderails and on the foot board

control panel come on when the brakes are disengaged.

Run through each function on the foot board control panel to ensure that each function is working properly.

Run through each function on both head end siderails to ensure that each is working properly.

If any problems are found during bed set

−

up, contact Stryker Customer Service at 800

−

327

−

0770.

Damaged Merchandise

ICC Regulations require that claims for damaged merchandise must be made with the carrier within fifteen

(15) days of receipt of merchandise.  DO NOT ACCEPT DAMAGED SHIPMENTS UNLESS SUCH DAMAGE

IS NOTED ON THE DELIVERY RECEIPT AT THE TIME OF RECEIPT.  Stryker Customer Service must be

notified immediately.  Stryker will aid the customer in filing a freight claim with the appropriate carrier for dam-

ages incurred.  Claim will be limited in amount to the actual replacement cost.  In the event that this information

is not received by Stryker within the fifteen (15) day period following the delivery of the merchandise, or the

damage was not noted on the delivery receipt at the time of receipt, the customer will be responsible for pay-

ment of the original invoice in full.
Claims for any short shipment must be made within thirty (30) days of invoice.

Summary of Contents for TriaDyne III Proventa 2030


















































































































Reviews:

No comments