Stryker Operating Room Information System Preinstallation Manual Download Page 47

Page: 47 / 56

Task

Stryker

Communications

Hospital Staff

Telco

3. LEC brings PRI to

POD in building

• Project Engineer -

verify analog line

to hub functions by

performing a test call

to the Hub.

• Project Manager -

obtain PRI info and

provide to Project

Engineer.

• Verify POD is where

requested.

• Obtain Circuit ID

and switch specifics.

• Provide to Stryker

Project Manager.

Brings PRI to POD.

4. Information for

PRI line obtained

Project Engineer -

program CODEC.

5. PRI wiring is ex-

tended to the Hub

room

Project Manager or

Install Team - Verify

Hospital wiring to the

Hub Room is correct.

Extend the Demarca-

tion to the Hub Room

using proper wiring.

6. Connect the PRI

to the Hub

• Connect the Hub to

the PRI line in hub

room.

• Verify IMUX light

comes up green.

7. Turn Up PRI Line Be present for testing

on site.

Be present for testing to

provide access to Hub

room for LEC.

Test line at POD and

Hub room.

8. Test PRI Line

Make both outgoing

and incoming calls.

Watch Switch Activity

and make any neces-

sary changes.

9. Verify Line

Registered with

ISDN provider

Call 1(800) 222-7956 to

verify.

done.

10. Ensure all PRI

information and

analog line to hub

go into Stryker

Install database

Project Manger - pro-

vide information to

Technical Support

Manager.

Summary of Contents for Operating Room Information System

























































Search results

Summary of Contents for Operating Room Information System

Reviews:

Brands by name

Popular brands

Stryker Operating Room Information System, Preinstallation Manual

Search results

Summary of Contents for Operating Room Information System

Reviews:

Brands by name

Popular brands