manualshive.com logo in svg

Stryker Operating Room Information System, Preinstallation Manual

Share
Download
Stryker Operating Room Information System Preinstallation Manual Download Page 31

 

   

   

27

S

7.2.3 

Level System Touch Panel (T)

Dimensions

•  Touch Panel: 11.9"W X 11.3"H X 6.6"D
•  Touch Panel Interface: 19"W X 2"H X 11"D

Power

One (1) duplex outlet

7.3 

Remote Level System Touch Panel (LTP) 

Dimensions

•  Touch Panel: 11.9"W X 11.3"H X 6.6"D
•  Touch Panel Interface: 19"W X 2"H X 11"D

Cabling

•  Cables provided by the Hospital/Contractor for runs over 50'
•  Cables pulled by the Hospital/Contractor
•  Leave a 15' (4.5m) services loop at each end for terminations
•  Cable Specifications:

 

º

Three (3) Belden 8723 or equivalent (maximum 1000')

 

º

One (1) Belden 8241 or equivalent (maximum 1000')

Conduit

One (1) 1" conduit

Back Box

•  4"W X 4"H junction box with single-gang mud ring
•  Mounted within 18" of touch panel location

Power

One (1) standard outlet within 18" of touch panel location

ITEM-ITEM

QTY

SIZE

LTP – S

1

1"

Summary of Contents for Operating Room Information System

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands