manualshive.com logo in svg

Stryker Operating Room Information System, Preinstallation Manual

Share
Download
Stryker Operating Room Information System Preinstallation Manual Download Page 41

 

   

   

37

S

10.1.2  Site Preparation Requirements

The following provide instructions that must be completed before installation.

10.1.2.1 

Status System Controller

Each Status System Controller can support up to sixteen (16) cameras. If there is a Video Network 

Hub, the Status System Controller will sit on top of it and will be powered through the Hub. This con-

troller will be operated by the touch panel.

Rough-in and cabling

One (1) 12" x 4" (300mm x 100mm) wall mounted cable chase from ceiling to 36" (1m) above the 

finished floor for cabling to each Fixed OR Status Camera. Leave up to 15' (4.5m) of cable on both ends 

of cable runs for Stryker Technician termination and cable management. If any of the cables exceed the 

maximum length specified, please consult your Project Manager for necessary amplification/transmis-

sion equipment. 

Power

This controller will plug into an outlet on the video network hub. If a hub is not present, one (1) stan-

dard electrical outlet is required. 

10.1.2.2 

Status Camera Power Supply

Each Camera Power Supply can support up to eight (8) cameras. The number of Camera Power Sup-

plies depends upon the number of Fixed OR Status Cameras. Please consult the Project Manager if it is 

unclear as to the number of Camera Power Supplies the site must be prepared for.

Rough-in and cabling

Hospital/Contractor must install this power supply (usually in the ceiling above the Video Network 

Hub) and will wire the cameras into the power supply. If a hub is not present, the placement of the 

power supply box is at the Hospital's discretion. 

Power

Hospital/Contractor must hard-wire this power supply to the 120V/60Hz Hospital power.

10.1.2.3        Wall/Ceiling Mounted Fixed Room Status Camera (WRC, CRC) 

LA

Conduit

One (1) ¾" conduit terminated at nearest corridor cable tray

Back Box

•  4"W x 4"H junction box with single-gang mud ring
•  Flush mounted at 12" below finished ceiling (wall mounted only)

Power

None

Cabling

•  One (1) power cable and one (1) video cable
•  One (1) Belden 8723 / 88723 (maximum 1000')
•  One (1) Belden 8241 / 88241 (maximum 1000')
•  Cables require 15' service loop at both ends

 

Note

All Status System cabling must be provided and pulled by the Hospital/Contrac-

tor prior to Stryker Installation.

Summary of Contents for Operating Room Information System

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands