STEYR MOTORS MO114K33 Operation, Maintenance And Warranty Manual Download Page 29

Page: 29 / 134

CAUTION:

In case of non-observance of break-in instructions, warranty may expire.

Engine to be filled with recommended oil quality only. See chapter “Engine Lubrication”.

Operation after Break-In

The engines specified in this manual are intended to be operated at different speeds and loads, but not allowing full-

load of the engine for more than one hour per 12 running hours. Economic driving may be achieved at the following

speeds:

4 Cylinder MO Marine Engines

MO54NA33

3000 rpm

MO84K32

3000 rpm

MO94K33

3000 rpm

MO114K33

3000 rpm

MO144M38

3200 rpm

MO164M40

3400 rpm

MO174V40

3400 rpm

4 Cylinder SE Marine Engines

6 Cylinder SE Marine Engines

SE144E38

3400 rpm

SE126E25

2300 rpm

SE164E40

3600 rpm

SE156E26

2400 rpm

SE156E32

3000 rpm

SE156E34

3200 rpm

SE196E35

3200 rpm

SE236E40

3800 rpm

SE236S36

3400 rpm

SE266E40

3800 rpm

SE266S36

3400 rpm

SE286E40

3800 rpm

SE306J38

3600 rpm

Which will prolong engine life and reduce sound emissions.

When starting a cold engine, always allow the engine to warm up slowly. Never run the engine at full speed until op-

erating temperature is reached. During the first 50 running hours, check the oil level frequently.

Summary of Contents for MO114K33







































































































































Search results

Summary of Contents for MO114K33

Reviews:

Related manuals for MO114K33

Brands by name

Popular brands

STEYR MOTORS MO114K33, Operation, Maintenance And Warranty Manual

Search results

Summary of Contents for MO114K33

Reviews:

Related manuals for MO114K33

Brands by name

Popular brands