STEYR MOTORS MO114K33 Operation, Maintenance And Warranty Manual Download Page 53

Page: 53 / 134

Disposal of Automotive Waste Products

Used fuel and oil is to be collected in separate containers to permit an eventual subsequent treatment.

THE DISPOSAL OF ANY FUEL AND OIL FOR THE ENGINE IS SUBJECT TO THE

SPECIAL WASTE ACT. THE “SPECIAL WASTE CATALOGUE” ÖNORM S2100 REFERS

TO THE NECESSARY DISPOSAL IN AUSTRIA. PLEASE FOLLOW THE LOCAL

REGULATIONS OF YOUR COUNTRY.

The operating and maintenance personnel has to take care that fuel and oil as well as other material ranking as spe-

cial waste are deposited at the respective collecting points.

Code No.

Designation

31 423

oil contaminated ground or oil binder

54 102

waste oil

54 104

fuel

54 202

grease

54 207

vaseline

54 917

compact sealing material

54 927

oil contaminated scouring cloth

54 928

usel oil- and air filters

55 510

colour- or varnish containing waste

Summary of Contents for MO114K33







































































































































Search results

Summary of Contents for MO114K33

Reviews:

Related manuals for MO114K33

Brands by name

Popular brands

STEYR MOTORS MO114K33, Operation, Maintenance And Warranty Manual

Search results

Summary of Contents for MO114K33

Reviews:

Related manuals for MO114K33

Brands by name

Popular brands