stertil ST1175 Service Manual Download Page 76

Page: 76 / 108

Operation & Service Manual (VA)

ST1175

8.4.6

No mains power

Cause

Solution

No mains power.

Have the fault corrected by a qualified
electrician.

Mains fuse has blown.

Replace the fuse.

The mains switch is

OFF

Set the mains switch to

Defective LEDs.

Contact the technical service.

8.4.7

No control voltage

Cause

Solution

Defective LEDs. Lifting system
functioning normally.

Contact the technical service.

The lifting system may not be set up
properly.

Follow the normal operation
procedures as stated in the Operator
Manual. If the fault occurs again,
contact the technical service.

A fuse has been tripped.

Check the F2 and F3 fuses.

Replace the fuse(s) in the control box if
necessary. If the fault occurs again,
contact the technical service.

The mains switch is

OFF

Set the mains switch to

Broken cable or loose connector.

Check the cable and connector.

The emergency stop button has not
been unlocked.

Unlock the button. Set the main switch
to

OFF

and

. Press the [SELECT]

button once to ensure the system can
be used again.

The thermal relay in the main box has
been deactivated.

Reset the thermal relay. Contact the
technical service if the problem
persists.

Summary of Contents for ST1175













































































































Search results

Summary of Contents for ST1175

Reviews:

Related manuals for ST1175

Brands by name

Popular brands

stertil ST1175, Service Manual

Search results

Summary of Contents for ST1175

Reviews:

Related manuals for ST1175

Brands by name

Popular brands