stertil ST1175 Service Manual Download Page 72

Page: 72 / 108

Operation & Service Manual (VA)

ST1175

Error
code

Code/label

Possible cause

Solution

Output power
supply fault

Defective power
supply to outputs.

Set the main switch(es) to
OFF.

Check and replace fuse F2
(3.15A) if required. Also
check the thermal relay and
reset it if required. Turn on
the control box again using
the standard procedure. If
the fault occurs again,
contact the technical service.

Short circuit on
PCB

Short circuit on the
PCB.

Allow damp box to dry.

Replace PCB if the fault
persists.

EPROM read
fault

Turn OFF and ON on the
main switch(s) and press the
[SELECT] button to ensure
the system can be used
again. Replace the PCB if
required.

EPROM write
fault

Watchdog fault

General CAN
error

CAN timeout

8.4

Faults

The following troubleshooting guide can be used to help localize faults. If in doubt,
the user should contact the technical service.



In the event of malfunctions other than those described here, always consult the

technical service.

Summary of Contents for ST1175













































































































Search results

Summary of Contents for ST1175

Reviews:

Related manuals for ST1175

Brands by name

Popular brands

stertil ST1175, Service Manual

Search results

Summary of Contents for ST1175

Reviews:

Related manuals for ST1175

Brands by name

Popular brands