stertil ST1175 Service Manual Download Page 43

Page: 43 / 108

Operation & Service Manual (VA)

ST1175

For the functions of the switches, see next figure.

Emergency button

Main switch

DOWN

[SELECT] button

Unlocking

Slow lowering selection button

<FAULT> indicator

<ALL> indicator

10.

[SINGLE] indicator

11.

[PAIR] indicator

Master column

Slave column

Main power supply

To next column

Control boxes



Operate the panel only with your fingertips. Pressing the buttons using sharp

objects (such as screwdrivers) can damage the equipment and cause errors.

6.4.1

Emergency shutdown button

If the emergency shutdown button is pressed, all movement is immediately halted
(raising or lowering).

6.4.2

Starting

The main switch controls the power supply to the column lifts. This switch has two
positions:

0 (OFF)

This will interrupt the power supply to the column lift(s).

Summary of Contents for ST1175













































































































Search results

Summary of Contents for ST1175

Reviews:

Related manuals for ST1175

Brands by name

Popular brands

stertil ST1175, Service Manual

Search results

Summary of Contents for ST1175

Reviews:

Related manuals for ST1175

Brands by name

Popular brands