stertil ST1175 Service Manual Download Page 75

Page: 75 / 108

Operation & Service Manual (VA)

ST1175

8.4.3

The column lift lowers of its own accord

Cause

Solution

The cylinder seal is damaged; oil is
leaking continuously.

Have the technical service replace the
cuff or the cylinder.

Leak in the oil line couplings.

Tighten the couplings or union nuts.

Dirty or damaged non-return valve.

Have the non-return valve cleaned or
have it replaced by the technical
service.

Contaminated or damaged lowering
correction valve.

Have the valve cleaned or have it
replaced by the technical service.

8.4.4

The column lift is not raising far enough

Cause

Solution

Oil level in the tank is too low.

Top up with oil as described in section
Hydraulic oil.

Pump is drawing air.

Tighten or crimp the suction filter
attachment.

The steel plug has not been replaced
by the air bleed cap.

Fit the air bleed cap.

The air bleed cap is blocked.

Clean the air bleed cap.

8.4.5

The column lifts do not go up at the same speed

Cause

Solution

Control system not working correctly.

Use the S1 (UP) and S2 (DOWN)
switches in the control box to lift and
lower without having the safety
measures in place.

Operate the switches until the column
lifts are level. If the fault occurs again,
contact the technical service.

Summary of Contents for ST1175













































































































Search results

Summary of Contents for ST1175

Reviews:

Related manuals for ST1175

Brands by name

Popular brands

stertil ST1175, Service Manual

Search results

Summary of Contents for ST1175

Reviews:

Related manuals for ST1175

Brands by name

Popular brands