STEIN Radius Circuit 180 Operating Instructions Manual Download Page 10

Page: 10 / 62

STEIN300_Radius Circuit_06_GB.doc / 01.2020

3.4

Safety information for installation and repair work

DANGER!

In the area of the radius circuit due to an unexpected start up!

DANGER!

HIGH ELECTRICAL VOLTAGE!

Risk of electric shock!



1 Before carrying out any installation or repair work, disconnect the relevant radius

circuit from its electrical power supply.



2 Put up warning signs to prevent the system being started up while installation and

repair work is being done.



3 Remove all pallets from the affected radius circuit.



4 Carry out the work

•

in accordance with the descriptions in this documentation,

•

complying with relevant safety and accident prevention regulations and

•

in a technically correct manner and with the greatest possible accuracy.



5 After completing installation or repair work, carry out a test run of the entire sys-

tem and check that all safety features are functioning correctly.

DANGER!

Never operate the radius circuit using

•

defective safety equipment and / or

•

damaged components.

Summary of Contents for Radius Circuit 180































































Search results

Summary of Contents for Radius Circuit 180

Reviews:

Related manuals for Radius Circuit 180

Brands by name

Popular brands

STEIN Radius Circuit 180, Operating Instructions Manual

Search results

Summary of Contents for Radius Circuit 180

Reviews:

Related manuals for Radius Circuit 180

Brands by name

Popular brands