Spectra Watermakers Bimini 300 Installation And Operating Manual Download Page 25

Page: 25 / 78

Optional Tank Low Switch

Installing the tank low float switch

about 2/3rds down from the top of your water tank allows the Spectra Connect to run in Auto Fill

mode; automatically filling your water tank, stopping itself, fresh water flushing, returning to Auto

Store mode, and then turning itself on again to fill the tank when the water level drops below the

Tank Low Switch with no additional user commands.

Drill

5/8”

hole into the side of the fresh water tank that is being filled by the watermaker. This can

be installed wherever there in convenient access to the tank, approximately 2/3rds of the way down

from the top of the tank.

Drill

5/8”

hole

Tank Switch Installation

2/3

The float switch must be connected to the Tank Switch 1 terminals on the Spectra Connect

control board at the Feed Pump Module

There is no polarity.

For Instructions on enabling the

‘

Auto Fill

’

mode see the System Settings instructions

later in this manual.

Watermakers should never be run unattended!!

Tank Switch 1

Summary of Contents for Bimini 300















































































Search results

Summary of Contents for Bimini 300

Reviews:

Related manuals for Bimini 300

Brands by name

Popular brands

Spectra Watermakers Bimini 300, Installation And Operating Manual

Search results

Summary of Contents for Bimini 300

Reviews:

Related manuals for Bimini 300

Brands by name

Popular brands