Spectra Watermakers Bimini 300 Installation And Operating Manual Download Page 20

Page: 20 / 78

The Bimini 300 has a power inlet harness with a terminal block and cover, a boost pump power

plug with a yellow band, terminal block for the tank full switch and the optional tank level sen-

sor, and a short plug with a green band for the optional Z

Ion.

Do not install it in hot or poorly ventilated locations.

llow access to the motor speed

control

Power inlet harness

with terminal block

Boost pump cable (Yellow)

Brushless Motor speed

controller

Spectra Connect

controller (Inside control

Run Auto/Manual/Service

toggle switch

Electrical

ION Connector (with green band). Left

unused if your system was not ordered

with the optional Z

ION.

Tank Full Switch

Terminal Block,

Green + Orange

Tank Level sensor

5vdc: Red

Signal: White

Ground: Black

Standard Fresh Water

Flush connector (Blue)

Product manifold assemble (Red

connects left of Clark Pump)

Summary of Contents for Bimini 300















































































Search results

Summary of Contents for Bimini 300

Reviews:

Related manuals for Bimini 300

Brands by name

Popular brands

Spectra Watermakers Bimini 300, Installation And Operating Manual

Search results

Summary of Contents for Bimini 300

Reviews:

Related manuals for Bimini 300

Brands by name

Popular brands