Sourcetronic ST9010 Series User Manual Download Page 4

Page: 4 / 62

◇

4.5.1

After adding multiple scan channels, the instrument will add ................................................................................ 41

4.5.2

Structural principle ................................................................................................................................................. 42

4.6

Structure and Use of HANDLER and SINGNAL Interface Circuit ................................................................................ 42

4.6.1 Control Interface Theory .............................................................................................................................................. 42

4.6.2

HANDLER Control Interface Main Signal Timing Description ............................................................................ 43

4.7

File Storage Other interfaces and functions of the instrument ......................................................................................... 44

Chapter 5 Serial Port Commands Instruction .................................................................................................... 45

Brief Description of the Command Format: ................................................................................................................................................................... 45

5.1

DISPlay Subsystem Commands ...................................................................................................................................... 45

5.2

MMEM Subsystem Commands ....................................................................................................................................... 45

5.3

FUNCtion Subsystem Commands ................................................................................................................................... 46

5.3.1

FUNCtion test, Stop instruction .............................................................................................................................. 46

5.3.2

FUNCtion File Editing Function Commands ......................................................................................................... 46

5.3.3

FUNCtion Test Function, Test Parameter Commands ............................................................................................. 46

5.3.4

Specific Examples of Command Data Format ....................................................................................................... 47

5.4

SYSTem Subsystem Commands ..................................................................................................................................... 54

5.5

Other Commands ............................................................................................................................................................. 56

Chapter 6 Appendix ............................................................................................................................................... 58

Summary of Contents for ST9010 Series































































Search results

Summary of Contents for ST9010 Series

Reviews:

Related manuals for ST9010 Series

Brands by name

Popular brands

Sourcetronic ST9010 Series, User Manual

Search results

Summary of Contents for ST9010 Series

Reviews:

Related manuals for ST9010 Series

Brands by name

Popular brands