SECTION 1
GENERAL
1-1
This section is extracted from
instruction manual.
SLV-SE35/SE50/SE60/SE70/SE80/SX60/SX70/SX80
Getting Started
4
Getting Started
Step 1
Unpacking
Check that you have received the following items with the VCR:
• Remote commander
• R6 (size AA) batteries
• Aerial cable
• EURO-AV cable
(SE80, SX80 model)
Getting Started
Getting Started
5
Step 2
Setting up the remote commander
Inserting the batteries
Insert two R6 (size AA) batteries by
matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first, then
push in and down until the positive
(+) end clicks into position.
Using the remote commander
You can use this remote
commander to operate this
VCR and a Sony TV. Buttons
on the remote commander
marked with a dot (•) can be
used to operate your Sony TV.
If the TV does not have the
g
symbol near the remote sensor,
this remote commander will
not operate the TV.
To operate
the VCR
a Sony TV
Set TV / VIDEO to
VIDEO and point at the remote sensor on the VCR
TV and point at the remote sensor on the TV
continued
Remote sensor
TV / VIDEO
1
2
3
4
5
6
Getting Started
6
Step 2 : Setting up the remote commander (continued)
FASTEXT buttons
V
;
WIDE
…
TV/VIDEO
I/
u
AUDIO MONITOR
DISPLA
– /– –
– /– –
Y
Á
+/–
Programme
number
buttons
TV control buttons
To
Turn the TV into standby mode
Select an input source of the TV either from
aerial in or from line in
Select the programme position of the TV
Adjust the volume of the TV
Press
I
/
u
…
TV/VIDEO
Programme number buttons,
, PROG +/–
+/–
Á
PROG+/–/
√
/
◊
1
2
3
4
5
6
7
8
9
0
Getting Started
Getting Started
7
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
• Do not use a new battery with an old one together.
• Do not use different types of batteries together.
• Some buttons may not work with certain Sony TVs.
Controlling other TVs with the remote commander
The remote commander is preprogrammed to control non-Sony TVs. If your
TV is listed in the table below, set the appropriate manufacturer’s code
number.
1
Set TV / VIDEO at the top of the remote commander to TV .
2
Hold down
I
/
u
, and enter your TV’s code number(s) using the
programme number buttons. Then release
I
/
u
.
Now you can use the following TV control buttons to control your TV:
I
/
u
, TV/VIDEO, programme number buttons,
– / – –
(ten’s
digit),
PROG +/–,
Á
+/–,
;
(TV),
V
(Teletext), FASTEXT buttons, WIDE*,
MENU*,
>
*/
.
*/
?
*/
/
*, and OK*.
* These buttons may not work with all TVs.
Tip
• When you set your TV’s code number correctly while the TV is turned on, the TV
turns off automatically.
continued
To
Switch to TV (Teletext off)
Switch to Teletext
Select the sound
Use FASTEXT
Call up on-screen display
Change the Teletext page
Switch to/from wide mode of a Sony wide TV (For
other manufacture’s wide TV, see “Controlling other
TVs with the remote commander” below.)
Press
;
(TV)
V
(Teletext)
AUDIO MONITOR
FASTEXT buttons
DISPLAY
√
/
◊
WIDE
Summary of Contents for RMT-V256A
Page 83: ......
