manualshive.com logo in svg

Sony HDV HVR-A1U, Service Manual

Share
Download
Sony HDV HVR-A1U Service Manual Download Page 259

6-100

HVR-A1J/A1U/A1N/A1E/A1P/A1C

3-28.

Relay Gear, Conversion Gear

1. Removal procedure

1)

Remove the belt 

1

 from the conversion gear.

2)

Remove the washer 

2

 from the conversion gear shaft.

3)

Remove the conversion gear 

3

.

4)

Remove the relay gear 

4

.

2.

Attachment procedure

1)

Install the relay gear 

4

 in the relay gear shaft.

2)

Apply grease on the conversion gear shaft.
Amount of grease: A ball of grease of 1.0 mm diameter.

3)

Install the conversion gear 

3

 in the relay gear shaft.

4)

Install the washer 

2

 in the conversion gear shaft (Don’t re-use

the washer)

5)

Hook the belt 

1

 on the conversion gear and install it while

rotating the conversion gear.

Key Points
in Re-assembling

Points to be noted

Apply grease

Belt

2

 

Washer

4

 

Relay gear

3

 

Conversion gear

Relay shaft

Apply grease

Conversion 
gear shaft

Apply grease when installing
Amount of grease: A ball of 
grease of 1.0 mm diameter

Conversion 
gear shaft

Confirm that the belt doesn't run on the capstan motor block.
Check that the belt has no twisting, dirt, scratches, or grease 
splashes when installed.

Confirm that the belt does 
not run on the capstan 
motor block.

Ensure that belt 
has no twisting.

1

 

Belt

Don’t re-use the washer.

Points
to be noted

Summary of Contents for HDV HVR-A1U






















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands