manualshive.com logo in svg

Sony HDV HVR-A1U, Service Manual

Share
Download
Sony HDV HVR-A1U Service Manual Download Page 253

6-94

HVR-A1J/A1U/A1N/A1E/A1P/A1C

3-23.

GL (T) Block Ass’y, GL Arm (S) Ass’y

2.

Attachment procedure

1)

Enter the 

[ULE]

 mode.

2)

Installing the GL arm (S) ass'y
Install the GL arm (S) ass'y 

2

 to the GL arm (S) shaft, while

aligning the second gear of the GL rack with the phase
alignment mark.

3)

Installing the GL (T) block ass'y
Install the GL (T) block ass'y 

1

 to the GL (T) shaf, tin the

way that the GL (T) arm plate of the GL (T) block ass'y 

1

 is

placed parallel to the chassis.

1.

Removal

1)

Remove the GL (T) block ass’y 

1

 from the GL (T) shaft.

2)

Remove the GL (S) block ass’y 

2

 from the GL arm (S) shaft.

Key Points
in Re-assembling

Key Points
in Re-assembling

2

 GL arm ass'y (S)

GL rack

GL arm (S) shaft

GL (T) shaft

GL arm (T) shaft

GL (T) arm plate

GL (T) arm plate 
is placed parallel 
to the chassis.

1

 GL (T) block ass'y

Alignment mark

 

Summary of Contents for HDV HVR-A1U






















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands