manualshive.com logo in svg

Sony HDV HVR-A1U, Service Manual

Share
Download
Sony HDV HVR-A1U Service Manual Download Page 232

6-73

HVR-A1J/A1U/A1N/A1E/A1P/A1C

3-2.

Drum

2.

Attachment procedure

1)

Enter the 

[ULE]

 mode.

2)

Attach the flexible adhesive sheet 

4

.

3)

Hold the tape supporter block, and set the reference holes A
and B to the drum base reference pins A and B.

4)

Install the the drum 

3

 with the three screws (special head screw

M1.4 

×

 2.0) 

2

 in the order of 

B

, 

C

 and 

D

.

   Tightening torque: 0.04 

±

 0.01 N•m (0.41 

×

 0.1 kgf•cm)

5)

Attach the portion 

A

 of the drum flexible board to the flexible

adhesive sheet 

1

.

6)

Clean the tape path mechanism by referring to Section 2-2.
(Refer to Section “2-2. Tape Path System Cleaning”.)

7)

Implement the tape path adjustment. (Refer to Section “4-3.
Tape Path Adjustment”)

1.

Removal procedure

1)

Enter the 

[ULE]

 mode.

2)

Peel away the portion 

A

 of the drum flexible board from the

flexible adhesive sheet 

1

.

3)

Remove the three screws (special head screw M1.4 

×

 2.0) 

2

and remove the drum 

3

.

4)

Peel away the flexible adhesive sheet 

4

.

(Don’t re-use the flexible adhesive sheet. )

HOW TO PLACE 
THE MECHANISM

Drum (rear view)

Flexible adhesive sheet attachment position

B

C

D

A

Key Points
in Re-assembling

Points to be noted

Key Points in Re-assembling

After the flexible board is attached to the 
flexible adhesive sheet, place the flexible 
board, that is folded up, at the rear of the 
mechanism chassis to prevent the adhered 
portion from peeling away.

Cassette 
compartment 
assy

Don’t re-use the flexible 
adhesive sheet.

Points
to be noted

4

 Flexible adhesive sheet

1

 Flexible adhesive sheet

Tape supporter block

Reference pin A

3

 Drum

Reference pin B

Flexible board adhesive portion

Drum base blockassy

Flexible adhesive sheet

Attach the flexible adhesive sheet along the 
outer shape of the drum base block assy.

Attach the flexible board while aligning 
its side with the outer profile of the 
flexible adhesive sheet.

Flexible adhesive sheet

Slot 
(reference A)

Hole
(reference B)

Drum (rear view)

2

 Three screws (M1.4 

×

 2.0)

Summary of Contents for HDV HVR-A1U






















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands