background image

4-29

CCU-TX7 (E)/V1

4-7-4. INCOM Demodulation Adjustment

Note :

Perform this adjustment only when replacing 

1

T401/

AA-90 board.

Equipment

:

Oscilloscope, Audio generator

To be extended :

AA-90 board
AFM-15 board (CA-TX7/TX7P)

Preparetions :

1. Input the 1 kHz sine wave signal of the audio generator

to pin 2 (GND : pin 1) of INTERCOM/PROGRAM
connector (5 pin) on the CA-TX7/TX7P.

.

Fig-1 (Refer to 4-1-5. Audio connection.)

2. Adjust the output level control of audio generator so that

the pin 24 (GND : pin 12) /AFM-15 board is 220 mV p-p.

Test point :

TP14 (GND : E2)/AA-90 board

Adjustment Procedures :

1. Set the input range of oscilloscope to DC made. Adjust

the white core of 

1

T401/AA-90 board slowly so that the

DC level at TP14 (GND : E2)/AA-90 board  is 1.24 

±

0.01

V dc.

2. Set the input range of oscilloscope to AC mode, and adjust

the blue core of 

1

T401/AA-90 board so that the sine wave

is minimum.

3. Repeat procedure 1.

1.24 

±

 0.01 V dc

GND

Minimum

4-7-5. INCOM Level Adjustment

Equipment

:

Oscilloscope, Audio generator

To be extended :

AA-90 board

FM-15 board (CA-TX7/TX7P)

Preparetion :

1. Input the 1 kHz sine wave signal of the audio generator

to pin 2 (GND : pin 1) of INTERCOM/PROGRAM

connector (5 pin) on the CA-TX7/TX7P.

.

Fig-1 (Refer to 4-1-5. Audio connection.)

2. Adjust the output level control of audio generator so that

the pin 24 (GND : pin 12) /AFM-15 board is 220 mV p-p.

Test point

:

TP15 (GND : E2)/AA-90 board

Adjustment point :

1

RV401 (INCOM LEVEL)/

AA-90 board

Specifications

:

A = 220 

±

10 mV p-p

A

AA-90

PGM IN

MIC 1 LEVEL

MIC 2 LEVEL

MIC TEST

LEVEL IND

INTER COM

CLEAR

COM

(     )

2W

RTS

4W

RTS

CLEAR

COM

OFF

CH-2

CH-1

0dB

20dB

0dB

20dB

0dB

20dB

S2081

PGM IN

TP10

TP13

TP9

TP15

TP12

S201

MIC-1-LEV

S301

MIC-2-LEV

S2004

MIC TEST

INCOM

LEV

RV401

RV101

RV81

PGM

DEV

INCOM

DEV

S2006

RTS 200

OHM

OFF

ON

S2003

INCOM MODE

2CH

1CH

RV41

RV301

MIC 2

LEV

RV201

MIC 1

LEV

INCOM SELECT

S2002

RTS/CLEAR-COM

S2005

RV2000

SIDE TONE

LV1  3.0M

H CONT

LV21

2.5M CCU DATA

TONE TUNE

LV101  

5.6M TUNE

T201

T301

T401

LV41

3.6M

LV61

4.3M

AA-90 Board

 (A SIDE)

TP46

TP3005

TP3002

TP3004

TP3003

TP3001

TP43

TP7

TP2

TP5

TP6

E2

TP14

TP11

TP8

TP3

TP1

TP44

E12

E1

E11

E10

E3001

Summary of Contents for CCU-TX7

















































































Reviews: