1-12
CCU-TX7 (E)/V1
CCU-TX7/TX7P
English
To switch the DXC-D30WS/D30WSP
aspect ratio
To switch the DXC-D30WS/D30WSP Digital Video
Camera connected to this unit via the CA-TX7/TX7P
Camera Adaptor between 16:9 and 4:3 aspect ratios,
use the following methods.
When using the RCP-TX7 Remote Control
Panel
Switch the aspect ratio using advanced setting page
9/11 of the RCP-TX7’s OTHERS menu.
When using the COU-TX7 Camera Operation
Unit
Switch the aspect ratio using the DXC-D30WS/
D30WSP’s advanced menu.
Wide-aspect ID signals
When using the DXC-D30WS/D30WSP connected
to this unit via the CA-TX7/TX7P with the 16:9
aspect ratio, wide-aspect ID signals
1)
are added to the
video signals
2)
output from this unit.
It is possible to change the internal board settings of
this unit so that the ID signals are not added to the
video signals.
For more information about this, consult your Sony
service representative.
1) Complying with EIAJ CPR-1204 (CCU-TX7) or ETS
WSS (CCU-TX7P).
2) • Composite video signals 1 and 2 (output from the
VBS1 and VBS2 connectors)
• Video signal for video monitors (output from the PIX
connector)
• Video signal for waveform monitors (output from the
WF connector)
• Component video Y signal (output from the Y
connector)
• Y signal of Y and C signal output (output from the Y
connector)
3-864-243-01(1)
English
Pin assignment of the INTERCOM/TALLY
connector
The pin assignment for the unit’s INTERCOM/
TALLY connector (D-sub 25-pin) is as follows.
No.
Signal name
Specifications
1
GREEN TALLY (Y) IN ON: 24V DC/TTL(H)/Short
OFF: 0V DC/TTL(L)/Open
14
GREEN TALLY (X) IN
2
RED TALLY (Y) IN
ON: 24V DC/TTL(H)/Short
OFF: 0V DC/TTL(L)/Open
15
RED TALLY (X) IN
3
GND
Ground for intercom remote
signal
16
CAM MIC OFF IN
L: Camera intercom off
4
CH2 INT IN
L: Channel-2 interrupt on
17
CH1 INT IN
L: Channel-1 interrupt on
5
4W CH2 (R) (G) OUT
4-wire channel-2 system receive,
0 dBu balanced
18
4W CH2 (R) (Y) OUT
6
4W CH2 (R) (X) OUT
19
4W CH2 (T) (G) IN
4-wire channel-2 system talk,
0 dBu balanced
7
4W CH2 (T) (Y) IN
20
4W CH2 (T) (X) IN
8
2W CH2 (G) IN/OUT
2-wire channel-2 system,
0 dBu
Recommended termination
impedance: 600 ohms
21
2W CH2 (X) IN/OUT
9
4W CH1 (R) (G) OUT
4-wire channel-1 system receive,
0 dBu balanced
22
4W CH1 (R) (Y) OUT
10
4W CH1 (R) (X) OUT
23
4W CH1 (T) (G) IN
4-wire channel-1 system talk,
0 dBu balanced
11
4W CH1 (T) (Y) IN
24
4W CH1 (T) (X) IN
12
2W CH1 (G) IN/OUT
2-wire channel-1 system,
0 dBu
Recommended termination
impedance: 600 ohms
25
2W CH1 (X) IN/OUT
13
CHASSIS GND
Chassis ground
0 dBu=0.775 Vrms
1
2
3
4
5
6
7
8
9
13
14
15
16
17
18
19
20
21
22
23
24
25
11
12
10
