Sonifex DHY-04 Handbook Download

Page: 49 / 56

Technical Specification 7

Telephone Line Impedance:

ϲϬϬɏ͕ϵϬϬɏƉůƵƐϭϰŽƚŚĞƌĐŽŵƉůĞǆŝŵƉĞĚĂŶĐĞĐŝƌĐƵŝƚƐΎ

Rejection Ratio:

80-88dB on complex waveforms, reference peak level of 0dBFS

Ring Detector Sensitivity:

Off, 1, 2, 3, or 4 rings

Power Supply

Power to DHY-04, S & T

Universal 12W power supply: 90 to 250V AC; 47-63Hz; fused 1A

* These values are dependent on the actual country setting selected on the DHY-04

Connections

Mic/Line/AES-EBU Input:

XLR 3 pin female, with push-button mic/line selection

Line/AES-EBU Output:

XLR 3 pin male

Telephone Line:

RJ11 6/4 socket

Telephone Handset/Instrument:

RJ11 6/4 socket

Conferencing or Record Audio:

RJ45 socket

Remotes:

9-way D-type socket

Ethernet:

RJ45 socket

RS232 Serial:

9-way D-type socket

Power:

IEC mains (CEE22)

Accessories Order Code

Description

DHY-04CON

Front Panel Conversion Kit, DHY-04S to DHY-04

DHY-04SCON

Front panel conversion kit, DHY-04 free standing to DHY-04S 19” (48cm) rack-mount front

DHY-04TCON

Front panel conversion kit, DHY-04 or DHY-04S, to DHY-04T 19” (48cm) rack-mount front

DHY-04CONF

Conference Cable to Connect 2 x DHY-04(G) Units

Summary of Contents for DHY-04

























































Search results

Summary of Contents for DHY-04

Reviews:

Related manuals for DHY-04

Brands by name

Popular brands

Sonifex DHY-04, Handbook

Search results

Summary of Contents for DHY-04

Reviews:

Related manuals for DHY-04

Brands by name

Popular brands