Sonifex DHY-04 Page 13 Handbook Download | Manualshive

Page: 13 / 56

background image

3

What Is A Telephone Hybrid? 1

• Balanced output - 0dBu low impedance balanced output, with output

gain settings.

• Record output - the conferencing output can be set to give an output to

record just the caller or a mix of the caller and mic/line input signals for
recording both sides of the telephone conversation.

• Line limiter, bandpass filter and output noise gate with preset threshold

providing low distortion audio.

• Built in universal power supply between 90V AC and 250V AC, 47-63Hz,

IEC mains input.

• ETSI approval compliant with European PTT specifications.

Available Formats

The DHY-04 digital telephone hybrids are available in three different

DHY-04

Single automatic digital telephone hybrid, free standing

DHY-04S Single automatic digital telephone hybrid, rackmount
DHY-04T Twin automatic digital telephone hybrid, rackmount

DHY-04S Single Rackmount Automatic Digital TBU

Figure 1-2: DHY-04S Front & Rear.

DHY-04T Twin Rackmount Automatic Digital TBU

Figure 1-3: DHY-04T Front & Rear.

«
...
11
12
13
14
15
...
»

Summary of Contents for DHY-04

























































Reviews:

No comments

Related manuals for DHY-04

Ascotel Office 135

Brand: Aastra Pages: 2

Brand: Hama Pages: 22

Brand: Ibiza sound Pages: 47

Brand: Meridian Pages: 10

TRU341 - TRU 341 Cordless Phone

Brand: Uniden Pages: 20

Brand: Chamberlain Pages: 4

myPhone Jazz 202112

Brand: mPTech Pages: 65

Brand: Watts Pages: 16

Brand: QFX Pages: 7

Brand: Hama Pages: 53

Brand: Louroe Electronics Pages: 8

Brand: BRONDI Pages: 80

Brand: CDK Global Pages: 6

Face ID 5 Series

Brand: FingerTec Pages: 52

Brand: Unifat Pages: 7

Brand: Suzuki Pages: 150

Brand: Sound Projections Pages: 2

Brand: VisIC Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands