Sonifex DHY-04 Handbook Download | Manualshive

Page: 29 / 56

background image

19

Serial Port Control 5

5 Serial Port Control

DHY-04 Serial Connection

Default connection is 19200, e, 8, 1 and using XON/XOFF handshaking.

The serial port has reduced capability compared to the DHY-03 as the setup
and firmware functions have been removed and are implemented by an
embedded webserver.

SCI Software

Sonifex provide free of charge software, SCI, to allow you to manage
connection and control of all aspects of the serial port interface. Go to
www.sonifex.co.uk/sci for the latest version.

Serial Interface Commands & Responses

ANS:

- Answer Call

- ACK: or NAK:

BSV:

- BootStrap version

- BOOT:x.xx.xxx.xxx

CLR:

- Clear Call

- ACK: or NAK:

DTS:nnnn

- Send DTMF string nnnn

-ACK: or ERR:

MAC:

- MAC Request

- returns current MAC
address

NET:

- Network Request

- returns active
Network Parameters

SER:

-Serial Number Request

- SER:nnnnnnn

TEL:nnnnn

- Make Call

- ACK: or NAK: where
nnnnn is tel number
string or
#n for speed dial
numbers (1-7)
or #L for redial last
number

UID:

- Unit ID request

- UID:DHY-04

VER:

- version request

- VER:x.xx.xxx.xxx

SRQ:

- Status Request

- See Below

STA:01
STA:02
STA:03
STA:04
STA:05
STA:06

- Initialisation
- On Hook
- Ringing
- Off Hook - connected to line
- Dialling
- Firmware Update in progress

Error Messages

ERR:01

- Command Not Found

ERR:02

- Invalid Command (Error Unknown)

ERR:03

- Invalid Command (Invalid Parameter)

ERR:04

- Parameter out of range

ERR:05

- Write Parameter is Read Only

ERR:08

- Line Volts Missing

ERR:09

- Command not allowed when Call is Active

ERR:11

- Command not allowed when Call is Inactive

The telephone interface parameters are accessible from the webserver for
changing the settings for use on non-standard telephone systems or PABXs
and would not normally need to be changed on standard systems. They are
shown in Appendix A.

Many of these parameters are critical to the correct operation of the DHY-
04. Changing them may impact on the correct working of the unit or cause
the unit to operate in a way that is outside the telecom approval regimes.
Our advice is that the telephone interface parameters should not be
changed without detailed technical knowledge or input from Sonifex. Both
country code and disconnect type tables have reserved entries for future
additions - if you have special requirements for either of these parameters
please contact us with details and we can assess the demand and then add
to the standard list as required.

«
...
27
28
29
30
31
...
»

Summary of Contents for DHY-04

























































Reviews:

No comments

Related manuals for DHY-04

Brand: Panasonic Pages: 1182

Brand: Samsung Pages: 70

Brand: Samsung Pages: 21

Brand: Samsung Pages: 28

Brand: i-onik Pages: 6

Brand: i-MOBIL Pages: 10

Brand: Firstcom Pages: 37

Brand: Onn Pages: 11

2.4 GHz Digital Spread Spectrum Cordless Telephone with Call Waiting/Caller ID

Brand: Radio Shack Pages: 16

Brand: Elkay Pages: 2

Brand: Aastra Pages: 22

Brand: OCL Pages: 2

Brand: Galaxy Audio Pages: 12

Brand: switel Pages: 120

Brand: Radio Shack Pages: 24

Brand: Hall Technologies Pages: 30

Brand: Bridgesecure Technologies Pages: 4

Brand: Roadstar Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands