Sonifex DHY-04 Handbook Download | Manualshive

Page: 9 / 56

background image

iii

CE Conformity

details of the shipment. Packing materials should be kept for inspection and
also for if the product needs to be returned.

The product is shipped with the following equipment so please check to
ensure that you have all of the items below. If anything is missing, please
contact the supplier of your equipment immediately.

Item Quantity

Product unit

1

IEC mains lead fitted with moulded mains plug

1

Handbook and warranty card

1

If you require a different power lead, please let us know when ordering the
product.

Repairs & Returns

Please contact Sonifex or your supplier if you have any problems with your
Sonifex product. Email [email protected] for the repair/
upgrade/returns procedure, or for support & questions regarding the product
operation.

Conformity

The technical justification file for this product is available at Sonifex Ltd.

The declarations of conformity can be found at: http://www.sonifex.co.uk/
declarations

Conformity

The products in this manual comply with the essential requirements of the
relevant European health, safety and environmental protection legislation.

ACMA Conformity

The products in this manual also comply with the ACMA requirements for use
in Australia and New Zealand.

Safety & Installation of Mains

Operated Equipment

There are no user serviceable parts inside the equipment. If you should
ever need to look inside the unit, always disconnect the mains supply
before removing the equipment covers. The cover is connected to earth
by means of the fixing screws. It is essential to maintain this earth/
ground connection to ensure a safe operating environment and provide
electromagnetic shielding.

Voltage Setting Checks

Ensure that the machine operating voltage is correct for your mains power
supply by checking the box in which your product was supplied. The voltage
is shown on the box label. The available voltage settings are 115V, or 230V.
Please note that all products are either switchable between 115V and 230V,
or have a universal power supply.

Fuse Rating

The product is supplied with a single fuse in the live conducting path of the
mains power input. For reasons of safety it is important that the correct
rating and type of fuse is used. Incorrectly rated fuses could present a
possible fire hazard, under equipment fault conditions. The active fuse is
fitted on the outside rear panel of the unit.

Power Cable & Connection

An IEC power connector is supplied with the product which has a moulded
plug attached.

The mains plug or IEC power connector is used as the disconnect device.
The mains plug and IEC power connector shall remain readily operable to
disconnect the apparatus in case of a fault or emergency.

The mains lead is automatically configured for the country that the product
is being sent to, from one of:

«
...
7
8
9
10
11
...
»

Summary of Contents for DHY-04

























































Reviews:

No comments

Related manuals for DHY-04

Brand: Panasonic Pages: 268

Brand: Hansen Pages: 36

Brand: Aastra Pages: 2

Brand: Aastra Pages: 2

Brand: Aastra Pages: 2

Brand: Aastra Pages: 2

Dialog 4106 Basic

Brand: Aastra Pages: 2

Brand: EastLink Pages: 28

Brand: Aastra Pages: 461

Brand: Aastra Pages: 40

Brand: Aastra Pages: 47

Brand: Aastra Pages: 47

Brand: Ace Pages: 13

STAGE-4 ROKKER XXR Custom

Brand: J&M Corporation Pages: 5

Brand: Allison Transmission Pages: 190

Brand: Aastra Pages: 22

Brand: Uniden Pages: 60

Brand: Sven Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands