Sonifex DHY-04 Page 41 Handbook Download | Manualshive

Page: 41 / 56

background image

31

Webserver 6

Network Settings

The network page allows you to change the method of IP
assignment for the unit and to alter the Hostname used
by Bonjour for automatic connection regardless of the IP
address assigned.

Note: Submitting new network settings can cause the
browser to lose connection. the DHY-04 will attempt
to re-connect to the device and most browsers will

eventually

do this. The process is speeded up by

refreshing the page after 15 seconds, but some (notably
Internet Explorer) will not respond to this refresh and will
require a shut-down and restart, or you should wait a few
minutes then refresh the connection.

Bonjour Name

Enter the host name used by Bonjour. The Host name can
be up to 63 alphanumeric characters in length, and can
include hyphens (-). The default name is the Device ID
then ‘-’ then serial number without leading zeroes.

If a conflict occurs on the network this value will be
modified to ensure a unique name.

Static IP Address

Enter the static IP address that you wish to assign to this
unit. This IP address will be used if Dynamic addressing
is disabled. The default static IP address - and the IP
address when DIPSwitch 6 is active during power on - is
192.168.0.100

Figure 6-10: Network Page – settings for network interface.

«
...
39
40
41
42
43
...
»

Summary of Contents for DHY-04

























































Reviews:

No comments

Related manuals for DHY-04

Brand: NEC Pages: 7

Brand: NEC Pages: 2

Brand: NEC Pages: 3

Brand: NEC Pages: 144

Brand: Panasonic Pages: 8

Brand: Jabra Pages: 7

Brand: JBL Pages: 16

Authentics L 16

Brand: JBL Pages: 17

Brand: VTech Pages: 31

Brand: Akura Pages: 11

Brand: Sandstrom Pages: 32

Brand: BT Pages: 2

Brand: Verizon Pages: 55

Comfort Pro CM 300

Brand: T-Home Pages: 72

Brand: Gigaset Pages: 27

Brand: Uniden Pages: 55

Brand: Uniden Pages: 42

Maestro 4625 Owner's

Brand: Aastra Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands