manualshive.com logo in svg

Sonifex DHY-04, Handbook, Page: 16 / 56

Share
Download
Sonifex DHY-04 Handbook Download Page 16

2       Configuration & Controls - DHY-04, DHY-04S, DHY-04T

6

Rear Panel Controls & Connections

AES/EBU & Analogue Combined Line Output

The line output is an XLR 3 pin male connector with the following 

ĐŽŶŶĞĐƚŝŽŶƐ;y>ZͲϯͲϯϮ͕ϱϬɏďĂůĂŶĐĞĚĨůŽĂƚŝŶŐͿ͘/ƚŽƵƚƉƵƚƐĞŝƚŚĞƌďĂůĂŶĐĞĚ

analogue or AES/EBU audio by following the input, i.e. a digital input 
produces a digital output. 

Pin 1:  Screen 
Pin 2:  Phase 
Pin 3:  Non-Phase

Mic/Line & AES/EBU Input

dŚĞůŝŶĞŝŶƉƵƚŝƐĂŶy>ZϯƉŝŶĨĞŵĂůĞĐŽŶŶĞĐƚŽƌ;y>ZͲϯͲϯϭ͕ϭϬŬɏďĂůĂŶĐĞĚ

floating). It is autosensing for either analogue balanced or AES/EBU (left 
channel) signals.

Pin 1:  Screen 
Pin 2:  Phase 
Pin 3:  Non-Phase

Mic/Line Input Select Switch

This push-button switch sets the input signal mode:

Switch depressed (in) 

- Mic input mode selected 

 

Switch not depressed (out) 

- Line input mode selected

Adjusting the Microphone Gain Level

The Mic Level preset potentiometer controls the level of the input signal 
when the Mic/Line Input Select Switch is set to Mic input. The input signal 
level in Line mode is factory set and is not affected by this control. The Mic 

/ŶƉƵƚǁŝůůĂĐĐĞƉƚϮϬϬɏŵŝĐƌŽƉŚŽŶĞůĞǀĞůƐŝŐŶĂůƐĂŶĚŝƐďĂůĂŶĐĞĚͬĨůŽĂƚŝŶŐ

with a maximum gain of 70dB. Use a jeweller’s screwdriver to adjust the 
gain between 70dB and 52dB. The gain range can be extended by ±6dB by 
using the front panel ‘Level to The Line’ switch.

Remotes

The remote port allows you to control the line hold circuit from a mixing 
desk or other remote device and also outputs opto-isolated outputs to 
indicate the line hold status and the DTMF detect function. 

The remote connector is a 9-way female (socket) ‘D’ type. To remotely 
control the line connect, connect pin 1 to pin 2. The action of this remote 
can act as momentary or latching by pin 6 having no connection or 
connecting to 0V respectively.

Pins 3 & 7 is an opto-isolated remote line connect indicator and pins 5 & 7 
is an opto-isolated DTMF detect output. They can use the local supply pins 
4 & 8 to drive an LED indicator or a low current load.

Pin 1:  Remote Line Connect Switch 
Pin 2:   Common – 0V 
Pin 3:  Opto-Isolated Line Connect Indicator - NPN Emitter 
Pin 4:  Common – 0V  
Pin 5:  Opto-Isolated User GPO (DTMF Detect*) Indicator - NPN Emitter 
Pin 6:  User GPI (Momentary/Latch Line Connect Switch - connect to  
 

0V for latching action*) 

Pin 7:  Opto-Isolated Line Connect Indicator - NPN Collector 
Pin 8:  5V out (current limited supply for pins 7 & 9) 
Pin 9:  Opto-Isolated User GPO Indicator - NPN Collector 

The remote line connect indicator mimics the front panel Line Hold/
Connect Switch lamp, i.e. it flashes when ringing and is on when the line is 
held.

User GPO and GPI have their default functions (*) set to the same use as 
the DHY-03.

Conference Audio/Record Output

This is an RJ45 analogue audio connector to cross connect to another 
DHY-04. This will allow a single TBU channel on a mixing desk to handle 2 
calls, one to each DHY-04. Alternatively the conference output signals can 

Pin2  
Phase Signal

Pin 1  

Screen Signal

Pin 3  
Non-Phase Signal

Pin2  
Phase Signal

Pin 1  
Screen Signal

Pin 3  
Non-Phase Signal

Summary of Contents for DHY-04

























































Reviews:

No comments