Sokkia SDL30 Operator'S Manual Download Page 78

Page: 78 / 87

ifi

tio

The coefficient of linear expansion:

=20 x 10

-6

Aluminum staff

BAS55:

50mm (W) x 27.8mm (D) x 5005mm (H)

(5 sections)

{2.0in. (W) x 1.1in. (D) x 16.4ft (H)}

1.9kg (4.2lb.) (one staff) 2.2kg (4.9lb.)

(one staff and case)

The coefficient of linear expansion :

=24 x 10

-6

Measurement

Horizontal circle:

Diameter: 103mm

Graduation:1° / 1gon

Measuring range:*1

Height

0 to 4m (13.3 ft) (with BGS40 staff)

0 to 5m (16.7 ft) (with BGS50 staff)

SDL30:

0.0375 to 1.9305m (0.124 to 6.333 ft)

(with BIS20 staff)

0.0375 to 2.9725m (0.124 to 9.752 ft)

(with BIS30 staff)

Distance

1.6 to 100m

Minimum display:

Height

0.0001m / 0.001m (0.001 ft/0.01ft) (selectable)

(single, repeat, average or Wave-and-Read

mode)

0.001m / 0.01m (0.01ft/0.1ft) (tracking

mode)

Distance

0.01m (0.1ft) (single, repeat or average

mode)

0.1m (1 ft) (tracking or Wave-and-Read

mode)

Accuracy:*1

(with SOKKIA staff BGS40/50 or BIS20/30)

Height

Standard deviation for 1 km of double-run

SDL30:

Electronic Measurement

0.6mm (0.03in.) (with BIS20/30)

1.0mm (0.04in.) (with BGS40/50/50G)

1.2mm (0.047in.) (with BAS55)

Visual Measurement

1.0mm (0.04in.) (with BGS40/50/50G)

1.5mm (0.06in.) (with BAS55)

Summary of Contents for SDL30
























































































Search results

Summary of Contents for SDL30

Reviews:

Sokkia SDL30, Operator'S Manual, Page: 78 / 87

Search results

Summary of Contents for SDL30

Reviews: