Sokkia SDL30 Operator'S Manual Download Page 57

Page: 57 / 87

Oth

ced

16. Changing the Settings

You can change settings such as the measuring mode and the number

of decimals in displayed data.

When you select "Config." in menu mode, the two-page configuration

menu is displayed.

16.1 Measuring Mode

You can select any of the following measuring modes.

Page 1

* Single:

The instrument automatically terminates fine

measurement after taking one reading.

Average: Displays the average value calculated from the

number of times fine measurement is repeated.

(Repeat default setting: 5 times, Repeat setting

range: 2 to 9 times.)

Page 1

•

Meas. (measuring mode)

•

Display (fractional/decimal

representation of height units)

•

Adjust (checks and adjustment)

•

RS-232C (communication

parameters)

Page 2

•

Auto-off (auto power-off)

•

Unit (unit of measurement)

• Press

to toggle between the pages.

• Asterisks (*) indicate factory settings.
• Settings are kept in memory after power-off.
• "19.2 Adjusting the Reticle" for the check and adjustment

procedure.

Notes:

Summary of Contents for SDL30
























































































Search results

Summary of Contents for SDL30

Reviews:

Sokkia SDL30, Operator'S Manual, Page: 57 / 87

Search results

Summary of Contents for SDL30

Reviews: