Sokkia SDL30 Operator'S Manual Download Page 14

Page: 14 / 87

Int

duc

tion

•

Battery level (not displayed on menu screens)

Displays the current power level of the battery.

: Level 3: Full power.

: Level 2: Plenty of power remains.

: Level 1: Half or less power remains.

: Level 0: Little power remains. Charge the battery.

: Low: No power remains (A beep tone sounds and the

battery symbol blinks.) Charge the battery. Operation

cannot be performed. After a short time the instrument

automatically powers off.

•

Measurements

The following symbols are displayed.

: Staff reading (height)
: Horizontal distance to staff
: Height difference
: Elevation

The fractional/decimal display format for measurement value,

calculation value and input value depends on the settings in

measuring mode and fractional/decimal representation of height

units. (See "16. Changing the Settings".)

•

When the fractional/decimal display format is set to "0.0001m" and

the unit of measurement is "m", the display is as follows:

When measuring mode is "Single",

"Average" or "Repeat"

Height:

Up to 4 decimals

Distance: Up to 2 decimals
When measuring mode is "Tracking"

Height:

Up to 3 decimals

Distance: Up to 1 decimal

Summary of Contents for SDL30
























































































Search results

Summary of Contents for SDL30

Reviews:

Sokkia SDL30, Operator'S Manual, Page: 14 / 87

Search results

Summary of Contents for SDL30

Reviews: