Sokkia SDL30 Operator'S Manual Download Page 58

Page: 58 / 87

r Pr

oce

dur

Waving:

For measurement using Wave-and-Read

function

Repeat:

The instrument repeats fine measurements
until the operator presses

Page 2

Tracking: The instrument repeats coarse measurements

until the operator presses

16.2 Fractional/Decimal Representation of Height

Units

You can set the fractional/decimal display format for

displaying height values.

The following options are available when using "m" as the unit:

* 0.0001m: Up to 4 decimals (when measuring mode is

"single", "repeat", "average" or “Waving”)/Up to 3

decimals (when measuring mode is "tracking")

0.001m:

Up to 3 decimals ("single", "repeat", "average” or

“Waving”)/Up to 2 decimals ("tracking").

The following options are available when using "ft" as the unit:

* 0.001ft:

Up to 3 decimals (when measuring mode is

"single", "repeat" or "average")/Up to 2

decimals (when measuring mode is "tracking").

0.01ft:

Up to 2 decimals ("single", "repeat" or "average")/

Up to 1 decimal ("tracking").

Only the following option is available when using "inch" as

the unit:

1/8:

**-**-*/

Measure

• When

is pressed in Set-out mode, the Measurement

conditions setting screen can be displayed.

Note:

Summary of Contents for SDL30
























































































Search results

Summary of Contents for SDL30

Reviews:

Sokkia SDL30, Operator'S Manual, Page: 58 / 87

Search results

Summary of Contents for SDL30

Reviews: