Sokkia SDL30 Operator'S Manual Download Page 30

Page: 30 / 87

Sur

Setting Up Data Storage

Data can be stored in Height difference measurement mode or

Elevation measurement mode. JOB setting mode and record setting

mode must be set up before data can be recorded.

8.1

JOB Setting

Set the JOB containing the measurement data to be recorded.

Select from *JOB01 to JOB20.

JOB setting mode

Record setting mode

• *: Factory setting
• Settings are saved even after the instrument is turned off.
• Up to 2000 points can be registered. If 2000 points have already

been recorded, a beep tone sounds twice and the number of

free points remaining is displayed as "0". Measurement results

are not recorded. Press any button to return to the previous

screen.

• See "15.2 Data Output" and "14. JOB Delete" for how to "Output"

and "Delete" in the JOB setting mode.

• See "13. Displaying Recorded Data" for how to use "Review" and

"Memory" in the Record setting mode.

Notes:

• Between 1 and 12 characters can be set for the JOB name.
• If measurement data has already been saved in the selected

JOB, the unit of measurement (m or ft) cannot be changed. The

same unit of data will be applied in the future to data that is saved

to the same JOB.

• JOB names already used cannot be set.

Notes:

Summary of Contents for SDL30
























































































Search results

Summary of Contents for SDL30

Reviews:

Sokkia SDL30, Operator'S Manual, Page: 30 / 87

Search results

Summary of Contents for SDL30

Reviews: