manualshive.com logo in svg

Sokkia SDL30, Operator'S Manual, Page: 5 / 87

Share
Download
Sokkia SDL30 Operator'S Manual Download Page 5

4

Re

ad Th

is

 Firs

t

1.

Precautions for Safe Operation

For the safe use of the product and prevention of injury to operators

and other persons as well as prevention of property damage, items

which should be observed are indicated in this operator's manual by

WARNING and CAUTION indications.

The definitions of the indications are listed below. Be sure you

understand them before reading the manual's main text.

Definitions of Indications

•

Do not use voltage other than the specified power supply voltage.

Fire or electrical shock could result.

•

Do not use the unit in areas exposed to high amounts of dust or

ash, in areas where there is inadequate ventilation, or near

combustible materials. An explosion could occur.

•

Do not perform disassembly or rebuilding. Fire, electric shock or

burns could result.

•

Never look at the sun through the telescope. Loss of eyesight could

result.

•

Do not look at reflected sunlight from a prism or other reflecting

object through the telescope. Loss of eyesight could result.

 

•

Do not use the carrying case as a footstool. The case is slippery

and unstable so a person could slip and fall off it.

•

Do not place the instrument in a case with a damaged catch, belt or

handle. The case or instrument could be dropped and cause injury.

 WARNING

Ignoring this indication and making an operation
error could possibly result in death or serious
injury to the operator.

 CAUTION

Ignoring this indication and making an operation
error could possibly result in minor injury or
property damage.

General

Warning

Caution

Summary of Contents for SDL30
























































































Reviews:

No comments