manualshive.com logo in svg

Sokkia SDL30, Operator'S Manual, Page: 13 / 87

Share
Download
Sokkia SDL30 Operator'S Manual Download Page 13

12

Int

ro

duc

tion

•

Attribute•Measurement step display

Displays the backsight and foresight (in Height difference, Setting

out, or Measuring elevation modes).

: Backsight
: Foresight

Displays the attribute of the recorded measurement value (Height

difference measurement mode, Elevation measurement mode).

: Backsight point
: Foresight point
: Intermediate sight
: Fixed point
: Off

Displays the measurement step (when Adjustment is selected in

the Configuration mode).

At position A

: Take a reading on staff a.
: Take a reading on staff b.
: Take a reading on staff a with the tripod turned 180°.
: Take a reading on staff b with the tripod turned 180°.

At position B

: Take a reading on staff a.
: Take a reading on staff b.
: Take a reading on staff a with the tripod turned 180°.
: Take a reading on staff b with the tripod turned 180°. 

Displays the page number of the active menu (when the Menu

mode or Configuration mode is selected).

: First  page
: Second page

•

Measuring mode (not displayed on menu screens)

Displays the currently selected measuring mode.

: Single measurement
: Average measurement
: Wave-and-Read measurement
: Repeat measurement
: Tracking measurement

Summary of Contents for SDL30
























































































Reviews:

No comments