Sokkia SDL30 Operator'S Manual Download Page 62

Page: 62 / 87

r Pr

oce

dur

E410

E411

E412

E413

E414

E415

E416

E417

E418

E419

E420

E421

E422

E423

E424

E425

E426

E427

E428

E429

• An object other than the

staff is being sighted.

• The staff is out of focus.

• The staff is partly unread-

able because obscured

by an obstacle or dam-

aged.

• The staff is too close or

too far away.

• A shadow is falling on

part of the staff.

• The staff was incorrectly

sighted.

• Light is coming into the

eyepiece.

Use your hand or body to

shield eyepiece from light

source.

• The staff is set up in the

inverted position for

Wave-and-Read

measurement.

E430

E433

• Too bright.

• The brightness level sud-

denly altered during the

measurement.

• Something is shining

nearby or at back of the

staff.

• Light is coming into the

eyepiece.

• Use your hand or body to

shield eyepiece from light

source.

E431

• Something obscured the

staff or the brightness

level suddenly altered dur-

ing the measurement.

Error Message

Coded Message

Meaning

Summary of Contents for SDL30
























































































Search results

Summary of Contents for SDL30

Reviews:

Sokkia SDL30, Operator'S Manual, Page: 62 / 87

Search results

Summary of Contents for SDL30

Reviews: