Sokkia SDL30 Operator'S Manual Download Page 44

Page: 44 / 87

Sur

4 Measure the backsight.

The instrument takes the backsight

reading and displays the measure-

ment.

5 Select "Yes" to accept the value.

6 Measure the foresight.

The instrument calculates the differ-

ence between the measurement and

the input value, and displays the

result.

7 Move the staff by the amount shown

on the screen, then take another

foresight reading.
If "Fill" is displayed, move the staff

upward.

If "Cut" is displayed, move the staff

downward.

When the display shows '0', you have

found the specified ground point.

8 Press

or .

Height difference set-out is completed.

Set out the next ground point.

• When in this menu and setting-out has already been taken (for

the second or subsequent reading):
Step 4: The previous backsight measurement will be displayed

and the program skips to step 5.

• Storing setting out height difference:

Step 3: Even after power off, the height difference is stored.

Notes:

Summary of Contents for SDL30
























































































Search results

Summary of Contents for SDL30

Reviews:

Sokkia SDL30, Operator'S Manual, Page: 44 / 87

Search results

Summary of Contents for SDL30

Reviews: