Sokkia SDL30 Operator'S Manual Download Page 64

Page: 64 / 87

Oth

ced

18. Charging the Battery

1 Connect the power cable to the CDC68 charger and plug the

charger into the wall outlet.

2 Mount the battery (BDC46B) in the charger (CDC68) matching the

groove on the battery with the guides on the charger.
When charging starts, the lamp starts blinking.

• Do not short circuit. Heat or ignition could result.
• Batteries cannot be charged, even when the charging lamp is

flashing, when the temperature is outside the charging

temperature range.

• Do not leave the battery anywhere exposed to high

temperatures. Battery life may be reduced.

• Charge the battery once a month to maintain its quality when not

in use for long periods.

• Do not charge the battery just after charging is completed.

Battery performance may decline.

• Do not use to charge batteries other than those specified.
• If you allow the battery level to get too low, the battery may not be

rechargeable or operating time may decline. Keep the battery

always charged.

• The charger will get rather hot while in use. This is normal.

Important:

Procedure

Summary of Contents for SDL30
























































































Search results

Summary of Contents for SDL30

Reviews:

Sokkia SDL30, Operator'S Manual, Page: 64 / 87

Search results

Summary of Contents for SDL30

Reviews: