Sokkia SDL30 Operator'S Manual Download Page 42

Page: 42 / 87

Sur

• Point number input

Step 4:

Press

to ready the instrument for point

number input.

Step 6:

Press

twice to ready the instrument for

point number input.

(See "8.4 Flow of Recording Data".)

• Attribute setting

Step 6:

Press

to ready the instrument for attribute

setting. (See "8.4 Flow of Recording Data".)

• Go and Return setting

Step 4:

Press

to display the Go and Return Setting

Screen. (See "8.3 Double-run Measurement".)

• Storing backsight elevation

Steps 3 and 10: Even after power off, backsight elevation is

stored or turning point is stored as the next

backsight elevation. Since this value is the

same as the value in the setting out elevation

mode, the backsight elevation is stored to

whichever mode is set last. (See "11.3 Setting

Out Elevation".)

• Reviewing stored data

Steps 4 and 6: Press

to display the contents of the

selected JOB. (See "13.1 Data Check and Edit".)

• Manually inputting measurement data

Steps 4 and 6: Press

. Measurement data can now be

input manually. (See "8.4 Flow of Recording

Data".)

Notes:

Summary of Contents for SDL30
























































































Search results

Summary of Contents for SDL30

Reviews:

Sokkia SDL30, Operator'S Manual, Page: 42 / 87

Search results

Summary of Contents for SDL30

Reviews: