SMC Networks Barricade SMC7004VBR User Manual Download Page 35 | Manualshive

Page: 35 / 122

background image

C

ONFIGURING

THE

B

ARRICADE

4-7

PPPoE

Enter the PPPoE user name and password assigned by your Service
Provider. The Service Name is normally optional, but may be required by
some service providers.

Leave the Maximum Transmission Unit (MTU) on the default value (1492)
unless you have a particular reason to change it.

Enter a Maximum Idle Time (in minutes) to define a maximum period of
time for which the Internet connection is maintained during inactivity. If
the connection is inactive for longer than the Maximum Idle Time, it will
be dropped. Enable the Auto-reconnect option to automatically
re-establish the connection as soon as you attempt to access the Internet
again.

«
...
33
34
35
36
37
...
»

Summary of Contents for Barricade SMC7004VBR



























































































































Reviews:

No comments

Related manuals for Barricade SMC7004VBR

Brand: Watchguard Pages: 39

Brand: D-Link Pages: 213

Brand: CSS Pages: 2

Brand: FOR-A Pages: 2

Brand: Caimore Pages: 79

Brand: APM Pages: 3

Brand: Patton electronics Pages: 23

Brand: Freund Pages: 6

SW-UNM-24FE2GC-24POE

Brand: Morrell Pages: 8

Brand: Federal Signal Corporation Pages: 49

Brand: Solwise Pages: 231

Brand: Hawking Pages: 21

TGXPS-1080-M12-MV Series

Brand: ORiNG Pages: 2

Brand: Zhone Pages: 53

Brand: Net Optics Pages: 2

Brand: ENKHO Pages: 48

Brand: Camozzi Pages: 22

ClareVision CV-M161620-04

Brand: Clare Controls Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands