SMC Networks Barricade SMC7004VBR User Manual Download Page 22

Page: 22 / 122

NSTALLATION

2-4

Rear Panel

Figure 2-2. Rear Panel

Item

Description

6V 1A

Connect the included power adapter to this port.

Warning

: Using the wrong type of power adapter may cause

damage.

Reset

Use this button to reset the power or restore the default factory

settings. Reboot by pushing 1 second. Return all settings to the

factory defaults by pushing 5 seconds.

WAN

WAN port (RJ-45). Connect a cable modem, DSL modem, or an

Ethernet router to this port.

LAN

Four 10/100 Autosensing switch ports (RJ-45). Connect devices on

your local area network to these ports (such as a PC, hub, or switch).

WAN

LAN

Reset

Summary of Contents for Barricade SMC7004VBR



























































































































Search results

Summary of Contents for Barricade SMC7004VBR

Reviews:

Related manuals for Barricade SMC7004VBR

Brands by name

Popular brands

SMC Networks Barricade SMC7004VBR, User Manual

Search results

Summary of Contents for Barricade SMC7004VBR

Reviews:

Related manuals for Barricade SMC7004VBR

Brands by name

Popular brands