SMC Networks Barricade SMC7004VBR User Manual Download Page 14

Page: 14 / 122

NTRODUCTION

1-2

•

Firewall with Stateful Packet Inspection, client privileges, hacker
prevention, DoS, and NAT

•

NAT also enables multi-user access with a single-user account, and
virtual server functionality (providing protected access to Internet
services such as web, mail, FTP, and Telnet)

•

Virtual Private Network support using PPTP, L2TP, or IPSec
pass-through

•

User-definable application sensing tunnel supports applications
requiring multiple connections

•

Parental controls allows the user to limit certain web sites

•

Email alerts when the users network is being compromise

•

Easy setup through a web browser on any operating system that
supports TCP/IP

•

Compatible with all popular Internet applications

Summary of Contents for Barricade SMC7004VBR



























































































































Search results

Summary of Contents for Barricade SMC7004VBR

Reviews:

Related manuals for Barricade SMC7004VBR

Brands by name

Popular brands

SMC Networks Barricade SMC7004VBR, User Manual

Search results

Summary of Contents for Barricade SMC7004VBR

Reviews:

Related manuals for Barricade SMC7004VBR

Brands by name

Popular brands