SMC Networks Barricade SMC7004VBR User Manual Download Page 19

Page: 19 / 122

2-1

HAPTER

NSTALLATION

Before installing the Barricade

™

Broadband Router, verify that you have

the items listed under “Package Contents.” Also be sure that you have the
necessary cabling.

Package Contents

If any of the items are missing or damaged, contact your local SMC
distributor.

•

Barricade Broadband Router

•

Power adapter

•

One CAT-5 Ethernet cable

•

Four rubber feet

•

CD with User Guide

and EZ 3-Click Installation Wizard

•

Quick Installation Guide

•

SMC Warranty Registration Card

If possible, retain the carton and original packing materials in case there is
a need to return the product.

Summary of Contents for Barricade SMC7004VBR



























































































































Search results

Summary of Contents for Barricade SMC7004VBR

Reviews:

Related manuals for Barricade SMC7004VBR

Brands by name

Popular brands

SMC Networks Barricade SMC7004VBR, User Manual

Search results

Summary of Contents for Barricade SMC7004VBR

Reviews:

Related manuals for Barricade SMC7004VBR

Brands by name

Popular brands