SMC Networks Barricade SMC7004VBR User Manual Download Page 70

Page: 70 / 122

ETTING

TCP/IP

ORK

WITH

THE

ARRICADE

5-6

Windows 2000

1. Click the “Start” button and choose “Settings,” then click “Control

Panel.”

2. Double click the “Network and Dial-up Connections” icon, then

“Local Area Connection” icon, and press the “Properties” button in
the “General” tab.

3. Select the TCP/IP line that has been assigned to your network card in

the “Local Area Connection Properties” window.

4. Click the “Properties” button to set the TCP/IP protocol for the

Barricade.

5. You can dynamically assign TCP/IP address settings to a client, or you

can manually configure a client with address settings to meet your
specific network requirements. (Note that the default IP address of the
Barricade is 192.168.2.1.)

Summary of Contents for Barricade SMC7004VBR



























































































































Search results

Summary of Contents for Barricade SMC7004VBR

Reviews:

Related manuals for Barricade SMC7004VBR

Brands by name

Popular brands

SMC Networks Barricade SMC7004VBR, User Manual

Search results

Summary of Contents for Barricade SMC7004VBR

Reviews:

Related manuals for Barricade SMC7004VBR

Brands by name

Popular brands