SMC Networks Barricade SMC7004VBR User Manual Download Page 21

Page: 21 / 122

NSTALLATION

2-3

Front Panel

Figure 2-1. Front Panel

LED Indicators

The Barricade includes LED indicators on the front panel that simplify
installation and network troubleshooting.

Check the power and port indicators as shown in the following table.

LED

Condition

Status

Power

The Barricade is receiving power.

Flashing

The SMC7004VBR is initializing or upgrading

firmware.

WAN

The WAN port has established a valid network

connection.

Flashing

The WAN port is transmitting or receiving traffic.

Link/ACT On

The indicated LAN port has established a valid

network connection.

Flashing

The indicated LAN port is transmitting or

receiving traffic.

Speed

The indicated LAN port is operating at 100 Mbps.

Off

The indicated LAN port is operating at 10 Mbps.

Summary of Contents for Barricade SMC7004VBR



























































































































Search results

Summary of Contents for Barricade SMC7004VBR

Reviews:

Related manuals for Barricade SMC7004VBR

Brands by name

Popular brands

SMC Networks Barricade SMC7004VBR, User Manual

Search results

Summary of Contents for Barricade SMC7004VBR

Reviews:

Related manuals for Barricade SMC7004VBR

Brands by name

Popular brands